機床商務網
詳細介紹
QC11K數控液壓閘式剪板機
產品特點:
1.機架采用有限元分析設計，鋼板整體焊接結構，有很好的剛性和穩定性。
2.機架采用大型數控鏜銑床整體加工，保證剪切精度和質量。
3.刀架采用滾動導輪支撐，消除剪切間隙，提高剪切精度。
4.采用四刃剪刀，大大提高剪刀使用壽命。
5.刃口間隙手輪調節，刻度盤顯示，調整簡單、直觀、準確。
6.剪切行程可無級調節，以提高剪切效率。
7.采用串聯式油缸同步系統，蓄能缸回程，工作平穩可靠。
8.標配ESTUN21S剪板機數控系統，精度高，簡單易用。
QC11K數控液壓閘式剪板機
QC11Y Series Hydraulic guillotine beam shearing machine | |||||||
Specification | Shearing thickness (mm) | Shearing width （mm） | Strokes mm-1 | Backguage range (mm) | Shearing angler (°) | Workbench height （mm） | Main power （kw） |
QC11Y/K -6*2500 | 6 | 2500 | 10-35 | 20-600 | 1°30′ | 800 | 7.5 |
QC11Y/K -6*3200 | 6 | 3200 | 8-35 | 20-600 | 1°30′ | 800 | 7.5 |
QC11Y/K -6*4000 | 6 | 4000 | 7-35 | 20-600 | 1°30′ | 800 | 7.5 |
QC11Y/K -6*5000 | 6 | 5000 | 6-25 | 20-800 | 1°30′ | 900 | 11 |
QC11Y/K -6*6000 | 6 | 6000 | 5-25 | 20-800 | 1°30′ | 1000 | 11 |
QC11Y/K -8*2500 | 8 | 2500 | 10-35 | 20-600 | 1°30′ | 800 | 7.5 |
QC11Y/K -8*3200 | 8 | 3200 | 8-35 | 20-600 | 1°30′ | 900 | 7.5 |
QC11Y/K -8*4000 | 8 | 4000 | 7-35 | 20-600 | 1°30′ | 1000 | 15 |
QC11Y/K -8*5000 | 8 | 5000 | 6-25 | 20-800 | 0.5-2° | 1050 | 15 |
QC11Y/K -8*6000 | 8 | 6000 | 5-25 | 20-800 | 0.5-2° | 840 | 15 |
QC11Y/K -12*2500 | 12 | 2500 | 10-35 | 20-800 | 0.5-2.5° | 900 | 15 |
QC11Y/K -12*3200 | 12 | 3200 | 6-20 | 20-800 | 0.5-2.5° | 940 | 15 |
QC11Y/K -12*4000 | 12 | 4000 | 6-20 | 20-800 | 0.5-2.5° | 1000 | 15 |
QC11Y/K -12*5000 | 12 | 5000 | 5-15 | 20-800 | 0.5-2.5° | 1060 | 30 |
QC11Y/K -12*6000 | 12 | 6000 | 6-15 | 20-800 | 0.5-2.5° | 840 | 18.5 |
QC11Y/K -16*3200 | 16 | 3200 | 7-30 | 20-800 | 2°30′ | 900 | 30 |
QC11Y/K -16*4000 | 16 | 4000 | 6-30 | 20-800 | 2°30′ | 950 | 30 |
QC11Y/K -16*5000 | 16 | 5000 | 6-15 | 20-800 | 2°30′ | 1100 | 30 |
QC11Y/K -16*6000 | 16 | 6000 | 5-15 | 20-800 | 0.5-2.5° | 1100 | 37 |
QC11Y/K -20*2500 | 20 | 2500 | 9-30 | 20-1000 | 0.5-2.5° | 900 | 30 |
QC11Y/K -20*3200 | 20 | 3200 | 7-30 | 20-1000 | 0.5-3° | 950 | 30 |
QC11Y/K -20*4000 | 20 | 4000 | 6-30 | 20-1000 | 0.5-3° | 1100 | 30 |
QC11Y/K -20*5000 | 20 | 5000 | 5-30 | 20-1000 | 0.5-3° | 1100 | 37 |
QC11Y/K -20*6000 | 20 | 6000 | 5-15 | 20-1000 | 3° | 1200 | 45 |
QC11Y/K -25*2500 | 25 | 2500 | 5-25 | 20-1000 | 3° | 900 | 37 |
QC11Y/K -25*3200 | 25 | 3200 | 4-25 | 20-1000 | 0.5-3.5° | 950 | 37 |
QC11Y/K -25*4000 | 25 | 4000 | 3-20 | 20-1000 | 0.5-3.5° | 1100 | 37 |
QC11Y/K -32*2500 | 32 | 2500 | 4-12 | 20-1000 | 0.5-3.5° | 1000 | 55 |
QC11Y/K -32*3200 | 32 | 3200 | 4-12 | 20-1000 | 0.5-3.5° | 1100 | 55 |
QC11Y/K -40*2500 | 40 | 2500 | 3-10 | 20-1000 | 0.5-3.5° | 1200 | 60 |
QC11Y/K -40*3200 | 40 | 3200 | 3-10 | 20-1000 | 0.5-4° | 1200 | 60 |
Because in the continuous improvement of products, if there is difference between this date and technical data, should comply with the technical agreement parameters on both sides. No further notice! | |||||||
機床商務網