機床商務網
詳細介紹
產品參數
· 注意事項:
卡盤夾緊或松開操作時，配氣環上的兩個特制密封圈箍緊缸體外圓，所以卡盤的松開和夾緊必須在機床主軸停止旋轉時進行。
· CAUTION:
When clamping and releasing the chuck，the two special sealing rings on the valve ring block the cylinder outer circle.Therefore，the loosening and
clamping operations of the chuck must be carried out when the spindle of the machine stops rotating.
尺寸圖 Size Fig
尺寸參數 Dimensions(mm)
| 規格 Spec | A | A1 | B | C(H6) | D | E | F | M |
| 型號 Model | ||||||||
| 3KQ-350 | 380 | 315 | 192 | 235 | 275 | 7 | 115 | 6-M12 |
| 3KQ-400S | 467 | 400 | 194 | 310 | 374 | 5 | 152 | 9-M12 |
| 3KQ-400 | 223 | 150 | ||||||
| 3KQ-460 | 238 | 181 | ||||||
| 3KQ-500 | 510 | 313(338) | 325(300) | 360(330) | 10.5 | 205 | 12-M16 | |
| 3KQ-570 | 570 | 500 | 280 | 415 | 474 | 8 | 12-M12 | |
| 3KQ-570A | 230 | |||||||
| 3KQ-600 | 605 | 535 | 450 | 508 | 280 | |||
| 3KQ-630 | 685 | 610 | 305.5 | 510 | 580 | 325 | ||
| 3KQ-730 | 730 | 658 | 301.5 | 560 | 630 | 10.5 | 355 | 12-M16 |
| 3KQ-850 | 850 | 775 | 352 | 700 | 745 | 8 | 375 | |
| 3KQ-900 | 900 | 440 | ||||||
| 3KQ-1000 | 1000 | 850 | 330 | 815 | 10 | 560 | ||
| 3KQ-1150 | 1150 | 1060 | 352 | 800 | 1000 | 660 |
性能參數 Specifications
| 規格 Spec | 單爪行程 Single jaw stroke(mm) | 夾緊力(氣壓0.5Mpa時) Gripping force (Air0.5Mpa)KN(kgf) | 極限轉速 Max. Speed (r/min) | 慣量 Moment of inertial (kg.m2) | 重量 Weight(kg) | 大使用壓力 Max. pressure MPa(kgf/cm2) |
| 型號 Model | ||||||
| 3KQ-350 | 13+7 | 62(6326) | 3000 | 1.62 | 110 | 0.2-1(2-10) |
| 3KQ-400S | 7 | 130(13265) | 1700 | 5.6 | 154 | |
| 3KQ-400 | 13+7 | 1300 | 6.5 | 200 | ||
| 3KQ-460 | 110(11220) | 9.8 | 190 | |||
| 3KQ-500 | 17+7 | 140(14286) | 15.5 | 298 | ||
| 3KQ-570 | 17+8.5 | 160(16326) | 16.4 | 340 | ||
| 3KQ-570A | 140(14286) | 16.1 | 325 | |||
| 3KQ-600 | 160(16326) | 1100 | 19 | 360 | ||
| 3KQ-630 | 180(18367) | 900 | 28 | 520 | ||
| 3KQ-730 | 15+10 | 190(19388) | 800 | 44.2 | 583 | |
| 3KQ-850 | 13.4+12 | 200(20408) | 750 | 71.2 | 970 | 0.3-1(3-10) |
| 3KQ-900 | 190(19388) | 700 | 105 | 980 | ||
| 3KQ-1000 | 15+10.4 | 170(17347) | 450 | 150 | 960 | |
| 3KQ-1150 | 230(23470) | 400 | 194 | 1890 |
注：1. 單爪行程=快速行程+夾緊行程，快速行程不能用于央緊。
2. 在氣路中應配置減壓閥、氣液分離器、油霧器等氣動元件，以提高卡盤壽命。
3. 卡盤的換向閥應選用中位泄壓式三位五通雙氣控制閥，只有在泄壓狀態下才能旋轉工作。
1.Single stroke== fast stroke+clamping stroke, fast stroke can not be used for clamping.
2.Pneumatic components such as pressure reducing valve, gas-liquid separator and oil sprayer shall be equipped in the gas path to improve the life of the chuck.
3.The valve should be a relief chuck three position five way double control valve selection, only in the state of pressure relief to work.
機床商務網