機床商務網
詳細介紹
TL鋼制拖鏈
TL系列拖鏈的主體是由鏈板（優質鋼板鍍鉻）支撐板（擠拉鋁合金）軸銷（合金鋼）等部件組成使電纜或橡膠管與拖鏈之司不產生相對運動，不產生扭曲變形，鏈板經鍍鉻處理外形效果新穎，結構合理，靈巧強度高，鋼性好不變形安裝方便，使用可靠，易拆裝，尤其是本產品采用了高強度耐磨材料，臺金錒為軸銷提高了產品的耐磨強度，彎曲更靈活阻力更小，降低了噪音從而可保證長時司使用不變形，不下垂。
由于本產品外觀精美，可在較大程度上增強機床設備的整體藝術美觀效果，增強我國機床機械設備在市場的競爭能力。
1拖鏈可適應zui大移動速度40米／分。
2拖鏈在zui大移動速度時，噪聲聲壓級不大于68分貝。
3拖鏈安全使用壽命不小于1 00萬攻（往復）。
TL series steel drag chains
TL series drag chains are mainly consisting of chain plate （ top quality stainless steel with chromium plated）, supporting board （extruded aluminium alloy） and pinshaft （alloy）, etc. There is norelative motions between the cables/rubber hoses and the drag chains,giving no deforming or twists. The chromium plated chain board has very nice-looking appearance and has very rational construction and flexible and high strength. It is reliable and easy to operate, install,dismantal or assemble. It is worthwhile mentioning that the antiwearing performance has been improved greatly due to wear resistant material and alloy pinshaft are used. The product is flexible to bending and has low resistance, giving low noises. It can be used for a very long period of time without any deformation or hanging down.
The product is nice-looking, which makes the machine tool unit nicer looking as a whole and makes the machine tools and machineries more competitive in the international market.
1. The drag chain can adapt to max. moving speed of 40m/sec.
2. When at the max moving speed, the sound pressure of noises shall not be greater than 68 db.
3. The service life of the drag chain shall not be less than 1 million times （reciprocating）.
TL型鋼制拖鏈主要參數 Main parameters
| 型號Type | TL65 | TL80 | TL95 | TL115 | TL125 | TL155 | TL180 | TL225 | TL250 | TL325 | TL350 |
| 節距（mm） Pitch | 65 | 80 | 95 | 115 | 125 | 155 | 180 | 225 | 250 | 325 | 350 |
| 彎曲半徑（mm） Bending radius | 75-185 | 100-300 | 115-300 | 150-350 | 200-750 | 200-750 | 250-650 | 350-1000 | 400-1000 | 350-1000 | 400-1000 |
| zui小和zui大寬度（mm） Minimum width of drag chain | 70-350 | 70-400 | 120-450 | 120-500 | 120-550 | 130-600 | 140-700 | 150-1200 | 150-1200 | 300-3500 | 350-2000 |
| 外高度（mm） Height of drag chain | 44 | 60 | 70 | 86 | 99 | 120 | 144 | 200 | 220 | 250 | 300 |
| 支撐板zui大孔徑中內高（mm） Max hole diameler of support plate | 30 | 35 | 40 | 60 | 70 | 80 | 90 | 120 | 140 | 200 | 250 |
| 允許不用支撐輪長度m When non-support wheelis allowed | 6 | 7 | 9 | 10 | 10 | 10 | 10 | 10 | 10 | 12 | 12 |
表1/table1
| 型號 Type | 支撐板型式 Support board type | e | f | b1 | a1～an D1～Dn |
| TL65 TL80 | I | 由用戶按 需要自定 By user | |||
| II | 10 | 8 | |||
| III | 3 | ||||
| TL95 TL115 | I | ||||
| II | 12 | 1 2 | |||
| III | 4 | ||||
| TL125 TL155 | I | ||||
| II | 12 | 12 | |||
| III | 5 | ||||
| TL180 | I II III | 15 | 15 | 6 | |
| TL225 | I II III | 22 | 15 | 8 | |
| TL250 | I II III | 22 | 1 5 | 8 | |
| TL325 | I II III | 30 | 18 | 10 | |
| TL350 | I II III | 30 | 18 | 10 |
表2/table2
| 型號＼參數 | hg | D | Cmin | J | k | m | l | 11 | 12 | l3 | 14 | d | h | s |
| TL65 | 44 | 30 | 4 | 13 | 17 | 14 | 95 | 75 | 45 | 5 | 15 | 7 | 22 | 3 |
| TL80 | 60 | 40 | 5 | 15 | 20 | 17 | 12.5 | 10 5 | 4.5 | 5 | 15 | 7 | 22 | 3 |
| TL95 | 70 | 46 | 5 | 25 | 30 | 26 | 125 | 105 | 65 | 10 | 20 | 9 | 35 | 4 |
| TL115 | 86 | 65 | 6 | 25 | 30 | 26 | 155 | 130 | 80 | 10 | 25 | 11 | 35 | 5 |
| TL125 | 96 | 75 | 6 | 25 | 30 | 25 | 155 | 130 | 80 | 10 | 25 | 11 | 48 | 5 |
| TL155 | 120 | 90 | 7 | 25 | 30 | 26 | 160 | 135 | 80 | 10 | 25 | 11 | 48 | 5 |
| TL180 | 144 | 110 | 7 | 25 | 35 | 29 | 210 | 175 | 115 | 10 | 30 | 13 | 72 | 6 |
| TL225 | 200 | 170 | 1 0 | 35 | 45 | 39 | 300 | 200 | 14C | 10 | 30 | 18 | 100 | 6 |
| TL250 | 220 | 180 | 1 0 | 35 | 47 | 41 | 300 | 200 | 14C | 18 | 30 | 18 | 120 | 6 |
| TL325 | 250 | 200 | 1 0 | 40 | 50 | 42 | 325 | 220 | 15C | 25 | 35 | 20 | 140 | 8 |
| TL350 | 300 | 230 | 1 0 | 40 | 42 | 42 | 350 | 250 | 15C | 25 | 35 | 20 | 160 | 8 |
拖鏈的選用
1支掣板內腔孔徑D1=d+≈0.1d（取整數）。其中d=電線電纜液氣鞍管的外徑。
2根橡支攆板內腔zui大孔徑Dmax來確定鏈板高度hg和拖鏈型號TLXX。
3根橡拖鏈功能要求來確定支攆板型式的拖鏈的彎曲半徑：
（1）當拖鏈需承載較大管纜負茍對應選用高強度支攆扳I型（整塊式）。
（2）當管纜的管婆頭尺寸大于支攆板內腔孔徑或須經常拆裝、維修等時，可選用支撐Ⅱ型。屬分開式類型。
（3）安裝管纜的規格品種較多時，可選用支撐板Ⅲ型（框架式）。
4根據安裝管纜的數量來決定支攆板寬度B1，從而可得拖鏈寬度B。
5拖鏈使用場合或受環境影響時，需要采用鋼帶防護支攆板時，請與本公司另行提出。
帶三條鏈板的拖鏈
因為支攆板zui大長度為600mm- 650mm，在較寬拖鏈上可以裝置一個或多個拖鏈鏈板。另外的原因是可提高料窄的拖鏈的穩定性，此外也可通過第三條鏈板將套管與電纜塥開。
注SLE型致參數D，12，e，TL型取f,j,k.
液壓管的彈性狀況
要注意液壓管在壓力下會伸長或縮短，因此，應考慮到鞍管的彈性系數，特別是在高壓及拖鏈長度較長的情況下，應引起注意。
Selection of Drag Chains
1. The hole diameter of the inner cavity of supporting board D1 = d+0.1d （take round number）. where,d=outside diameter of cables,wires, liquid/gas hoses.
2. The height of the supporting board and the model numberTLXX of drag chains depends on the the max. hole diameter of the inner cavity of the supporting.
3. The bend radius depends on the functions of the drag chains.
（1）. When there is a large load from larger calibre or cables on the drag chains, high strength model I supporting board （integral） should be used.
（2）. When the size of the connectors are greater than that of the hole diameter of the inner cavity of supporting board or frequent assembly or dismantal operations are required,type III supporting board （frame type） can be used.
4. The width of supporting board B1 can be decided according to the quantity of the cables installed so that the width of the drag chain B can be arrived.
5. When limited by locations or environment and if bracing board with steel straps are needed, please contact our company for solutions
Drag chains with 3 chain board
One or more drag chain boards can be installed on a wider drag chain, because the max. length of the supporting board is 600mm-
650mm. This arrangement can also improve the stability of the narrower chains. In this way, the conduit and the cables can be separated from
one another by a third chain board.
Note: Parameters D, 12, e be used for SLE type and f,j,k for TL type.
Elastic status for hydraulic pipes
Note that the pressure of a hydraulic pipe may extend or contractdownward, so the elasticity should be taken into consideration,
especially under high pressure or with long length.
訂貨舉例
拖鏈型號TL95，支撐板III型，彎曲半徑R，支撐板寬度、長度，拖鏈TL95Ⅲ-250×300×325×4750
I型-支撐板整體型3個孔每個孔Φ30
II型-支撐板上下分開例3個孔Φ30
III型-上下是鋁板內有隔離片
Example for an order
Drag chain model number TL95, supporting board III type, bendradius R,supporting board width length drag chain TL95III-250x300x325x4750
I-type Integral type of support board with 3 holes, hole`s diameter being 30
II-type To arrange the upper board and the lower board separay with 3 holes each, hole`s diameter being 30
III-type The upper one and the lower one are made of aluminium with spacer inside
標記意義Lengends:
TL II型系列 TL II series steel drag chains
TL III型系列 TL III series steel drag chains
機床商務網