機床商務網
詳細介紹
| 名稱 | 山特 | 成工研 | 德越 | 澳克泰 | 進口泰珂洛 |
| 導向鍵 | 800-06A PM1 | DQ06A | 800-06A PM01 | / | GP06 F1122 |
| 導向鍵 | 800-07A PM1 | DQ07A | 800-07A PM01 | / | GP07 F1122 |
| 導向鍵 | 800-08A PM1 | DQ08A | 800-08A PM01 | / | GP08 F1122 |
| 導向鍵 | 800-10A PM1 | DQ10A | 800-10A PM01 | / | GP10S F1122 |
| 導向鍵 | 800-12A PM1 | DQ12A | 800-12A PM01 | / | GP12 F1122 |
| 導向鍵 | 800-14D065 PM1 | / | / | ||
| 導向鍵 | 800-20D100 PM1 | / | / | ||
| 外刀片 | 800-060308H-P-G 1025 | P060308-G/L | / | / | FBH06003RG-P UC2220 |
| 外刀片 | 800-08T308H-P-G 1025 | P08T308-G/L | 800-08T308M-P-G DY120 | APHT08T308P-DH AP301U(N) | FBH07504RG-P UC2220 |
| 外刀片 | 800-09T308H-P-G 1025 | P09T308-G/L | 800-09T308M-P-G DY120 | APHT09T308P-DH AP301U(N) | FBH09004RG-P UC2220 |
| 外刀片 | 800-11T308H-P-G 1025 | P11T308-G/L | 800-11T308H-P-G DY120 | APHT11T308P-DH AP301U(N) | FBH11004RG-P UC2220 |
| 大外刀片 | R424.9-130608-22 1025 | P13T308-G/L | R424.9-13T308-22 DY120 | APMT13T308-DH/LH AP301U(N) | FBH13004RG-P UC2220 |
| / | P14T308-G/L | / | / | ||
| 大外刀片 | R424.9-180608-23 1025 | P180608-G/L | R424.9-180608-22 DY120 | APMT180608-DH/LH AP301U(N) | |
| / | P19T308-G/L | / | / | ||
| 中心刀片 | / | C05T308-G/L | / | / | FBM05503LG-C UC2220 |
| 中心刀片 | 800-06T308M-C-G 1025 | C06T308-G/L | / | / | FBM06504LG-C UC1125 |
| 中心刀片 | 800-08T308M-C-G 1025 | C08T308-G/L | 800-08T308M-C-G DY120 | EPMT08T308C-DH AP301U(N) | FBM08004LG-C UC2220 |
| 中心刀片 | 800-10T308M-C-G 1025 | C10T308-G/L | 800-10T308M-C-G DY120 | EPMT10T308C-DH AP301U(N) | FBM09504LG-C UC2220 |
| 中心刀片 | 800-12T308M-C-G 1025 | C12T308-G/L | 800-12T308M-C-G DY120 | EPMT12T308C-DH AP301U(N) | FBM12504LG-C UC2220 |
| 中心刀片 | / | C13T308-G/L | / | / | |
| 中心刀片 | / | C19T308-G/L | / | / | |
| 中間刀片 | 800-06T308M-I-G 1025 | I06T308-G/L | / | / | FBM05503RG-I UC2220 |
| 中間刀片 | 800-08T308M-I-G 1025 | I08T308-G/L | 800-08T308M-I-G DY120 | EPMT08T308I-DH AP301U(N) | FBM06504RG-I UC2220 |
| 中間刀片 | 800-12T308M-I-G 1025 | I12T308-G/L | 800-12T308M-I-G DY120 | EPMT12T308I-DH AP301U(N) | FBM08004RG-I UC2220 |
| 中間刀片 | / | I13T308-G/L | / | / | FBM09504RG-I UC2220 |
| 中間刀片 | / | I19T308-G/L | / | / | FBM12504RG-I UC2220 |
| 中間刀片 | |||||
| 小三角 | TPMT16T312R-22/23 1025 | TPMT16T312-G | TPMT16T312R-22 DY120 | TPMT16T312R-DH/LH AP301U(N) | |
| 大三角 | TPMT220612R-22/23 1025 | TPMT220612-G | TPMT220612R-22 DY120 | TPMT220612R-DH/LH AP301U(N) | |
| / | TPMX14R/L | TPMX14R-Y | / | ||
| / | TPMX17R/L | TPMX17R-Y | / | ||
| / | TPMX24R/L | TPMX24R-Y | / | ||
| / | TPMX28R/L | TPMX28R-Y | / |
深孔鉆頭分為焊接式深孔鉆頭和機加式深孔鉆頭，深孔鉆頭都是采用內排屑，焊接式深孔鉆頭的刀片是不可以調換的，一次性使用，機加式深孔鉆頭的刀片是可以互換的，機加式深孔鉆頭的刀體可以長期使用，刀片可以換下。
- 精度高
- 材料好
- 高效傳動
- 適用范圍廣
機床商務網